KNX line limits come down to five numbers for one twisted-pair line: up to 64 devices with a 640 mA power supply, up to 350 m of cable from the supply to the furthest device, up to 700 m between any two devices, up to 1,000 m of cable in total, and no more than two power supplies. When a design goes past any one of them, add a line with a line coupler instead of stretching the first.
What is a KNX line?
A line is one section of twisted-pair bus cable with its own power supply. Every device on it takes power from the bus and talks over the same pair, at 30 V DC SELV. A line can be a straight run, a star or a tree. It cannot be a ring.
The five limits below come from the Ekinex 640 mA power supply datasheet and the ABB KNX system manual, as set out in our KNX cable guide. Check the datasheet of the exact power supply and cable you use, because it governs your project.
What are the limits?
| Limit | Value |
|---|---|
| Devices on one line | Up to 64, with a 640 mA power supply |
| Power supply to the furthest device | Up to 350 m along the cable |
| Between any two devices | Up to 700 m |
| Total cable on one line, all branches | Up to 1,000 m |
| Power supplies on one line | No more than two |
| Between two supplies on the same line | At least 200 m |
The 350 m figure is measured along the cable, not in a straight line across the building. A line can branch, but all the branches together stay within 1,000 m.
Why is 64 not always 64?
The device count depends on the power supply as much as on the standard. Each device draws current from the bus, so the supply must have enough to feed all of them. Sixty-four devices that each draw little are fine on a 640 mA supply. A line with several devices that draw more, such as some panels and gateways, may reach the supply's limit before it reaches 64. Add up the current figures in the datasheets.
KNX has also introduced a topology called TP1-256, announced by the KNX Association, which allows more devices per line and needs fewer line repeaters. It applies to devices that support it and still depends on power supply limits. A TP1-64 device counts as four against the 256 total. For a home project, the classic 64-device line is the safe planning figure unless your integrator says otherwise.
What about a second power supply?
A second supply on the same line is allowed, and it is not a free pass. The sources we use give a distance of at least 200 m between the two supplies, and the exact rule depends on the supply's datasheet. Also, a second supply is not a way to make one line longer: the 1,000 m total and the 350 m and 700 m limits still apply. In a villa the usual answer is not a second supply on the same line but a second line.
When should you add a line?
- The count is approaching 64 devices, with no headroom for later additions.
- The cable length is approaching 350 m from the supply, or 1,000 m total.
- The current drawn is approaching the supply's rating.
- The building has natural zones, such as floors or wings, which suit separate lines.
A line coupler joins one line to the next and filters traffic, so that messages for one line stay on that line. Each line has its own power supply, so adding a line adds capacity in cable, devices and power at once.
How large can a system get?
KNX organises lines into areas. The topology allows up to 15 areas of 15 lines, which at 64 devices per line gives room for 14,400 devices in the main lines, before counting the area and backbone lines. A house will not come near that, but the structure matters for a hotel or a large building.
A planning habit
Draw the lines on the floor plan first. Decide which devices sit on which line and where each supply goes, and leave at least a quarter of each line's capacity free. A line that is full on day one is a line that needs rework when the owner adds a room.
Questions people ask
How many devices can one KNX line have?
Up to 64 on a line with a 640 mA power supply, when the current drawn by the devices stays within the supply's rating. Newer TP1-256 devices allow more, subject to power limits.
How long can a KNX cable be?
Up to 1,000 m in total on one line, up to 350 m from the power supply to the furthest device, and up to 700 m between any two devices.
Can I add a second power supply to stretch a line?
No. A second supply does not lift the length limits. The sources we use call for at least 200 m between supplies, and the usual answer is a new line with a line coupler.
Planning lines and supplies for a project? Send us the device list and we will help check the numbers: talk to our team. For the wider picture see our KNX guide for India.
Sources checked on 7 November 2026
- Morion Automation, KNX cable in India, for the line limits and their sources.
- Ekinex, 640 mA KNX power supply datasheet, and ABB, KNX system manual, for the limits.
- KNX Association, The new KNX TP1-256 topology, for more devices and fewer line repeaters.
KNX line limits come down to five numbers for one twisted-pair line: up to 64 devices with a 640 mA power supply, up to 350 m of cable from the supply to the furthest device, up to 700 m between any two devices, up to 1,000 m of cable in total, and no more than two power supplies. When a design goes past any one of them, add a line with a line coupler instead of stretching the first.
What is a KNX line?
A line is one section of twisted-pair bus cable with its own power supply. Every device on it takes power from the bus and talks over the same pair, at 30 V DC SELV. A line can be a straight run, a star or a tree. It cannot be a ring.
The five limits below come from the Ekinex 640 mA power supply datasheet and the ABB KNX system manual, as set out in our KNX cable guide. Check the datasheet of the exact power supply and cable you use, because it governs your project.
What are the limits?
| Limit | Value |
|---|---|
| Devices on one line | Up to 64, with a 640 mA power supply |
| Power supply to the furthest device | Up to 350 m along the cable |
| Between any two devices | Up to 700 m |
| Total cable on one line, all branches | Up to 1,000 m |
| Power supplies on one line | No more than two |
| Between two supplies on the same line | At least 200 m |
The 350 m figure is measured along the cable, not in a straight line across the building. A line can branch, but all the branches together stay within 1,000 m.
Why is 64 not always 64?
The device count depends on the power supply as much as on the standard. Each device draws current from the bus, so the supply must have enough to feed all of them. Sixty-four devices that each draw little are fine on a 640 mA supply. A line with several devices that draw more, such as some panels and gateways, may reach the supply's limit before it reaches 64. Add up the current figures in the datasheets.
KNX has also introduced a topology called TP1-256, announced by the KNX Association, which allows more devices per line and needs fewer line repeaters. It applies to devices that support it and still depends on power supply limits. A TP1-64 device counts as four against the 256 total. For a home project, the classic 64-device line is the safe planning figure unless your integrator says otherwise.
What about a second power supply?
A second supply on the same line is allowed, and it is not a free pass. The sources we use give a distance of at least 200 m between the two supplies, and the exact rule depends on the supply's datasheet. Also, a second supply is not a way to make one line longer: the 1,000 m total and the 350 m and 700 m limits still apply. In a villa the usual answer is not a second supply on the same line but a second line.
When should you add a line?
- The count is approaching 64 devices, with no headroom for later additions.
- The cable length is approaching 350 m from the supply, or 1,000 m total.
- The current drawn is approaching the supply's rating.
- The building has natural zones, such as floors or wings, which suit separate lines.
A line coupler joins one line to the next and filters traffic, so that messages for one line stay on that line. Each line has its own power supply, so adding a line adds capacity in cable, devices and power at once.
How large can a system get?
KNX organises lines into areas. The topology allows up to 15 areas of 15 lines, which at 64 devices per line gives room for 14,400 devices in the main lines, before counting the area and backbone lines. A house will not come near that, but the structure matters for a hotel or a large building.
A planning habit
Draw the lines on the floor plan first. Decide which devices sit on which line and where each supply goes, and leave at least a quarter of each line's capacity free. A line that is full on day one is a line that needs rework when the owner adds a room.
Questions people ask
How many devices can one KNX line have?
Up to 64 on a line with a 640 mA power supply, when the current drawn by the devices stays within the supply's rating. Newer TP1-256 devices allow more, subject to power limits.
How long can a KNX cable be?
Up to 1,000 m in total on one line, up to 350 m from the power supply to the furthest device, and up to 700 m between any two devices.
Can I add a second power supply to stretch a line?
No. A second supply does not lift the length limits. The sources we use call for at least 200 m between supplies, and the usual answer is a new line with a line coupler.
Planning lines and supplies for a project? Send us the device list and we will help check the numbers: talk to our team. For the wider picture see our KNX guide for India.
Sources checked on 7 November 2026
- Morion Automation, KNX cable in India, for the line limits and their sources.
- Ekinex, 640 mA KNX power supply datasheet, and ABB, KNX system manual, for the limits.
- KNX Association, The new KNX TP1-256 topology, for more devices and fewer line repeaters.
